Ground clearance

How much you got, sitting in and loaded? Tell what your sxs is and what set up you have. :D

13-1/2, 07 660. At the side frame rails, it don't change with me in it.........

I cant mesure with me sitting in it.
but with all tools and cooler like ready for a ride.
i am around 17 1/2. i dont think it moves much when i get in.
but maybe with me in it. 16 3/4 or 17.
I can gain 3/4 of an inch if i run the shocks up. but it
rides like crap......

ChrisC wrote:

I cant mesure with me sitting in it.
but with all tools and cooler like ready for a ride.
i am around 17 1/2. i dont think it moves much when i get in.
but maybe with me in it. 16 3/4 or 17.
I can gain 3/4 of an inch if i run the shocks up. but it
rides like crap......

How do you get 17 1/2" with a 2" lift and 27's? You need to put that pee-pee ruler away. :(lmao:

Hell marty. these XTR's mesure over 3 inches taller than my stock ones.
when i go out i will check again where are yall mesureing from
the side or the skids....

From the ground to the bottom of the roll cage under the drivers door. I have bilsteins and 25" and have 11 1/2". If your tires are 3" taller they only give you 1 1/2" more clearance + 2" lift you should be around 15".

I gotta see 17 1/2" clearance on a Rhino. I have a 2" lift with EPI HD Springs and only have 11" of rear clearance once I have ridden for a while and everything has settled. I used to have 9" of clearance and the stability was much better. I bet a Rhino with 17 1/2" of clearance could be blown over in a strong wind -- I'd hate to ride that on much off-camber.

I will recheck it.....
i maybe wrong. i will look

You may not be far off Chris when unloaded and the suspension is lifted. If I jack my Rhino up to change a wheel and then set it down i can have 14". Once I drive it around and let the suspension spread and settle then I'll be down around 11". I've seen pics of Rhino's over a 5gal bucket but that is normally an unsettled suspension with some lift.

wvyankee2 wrote:

How do you get 17 1/2" with a 2" lift and 27's? You need to put that pee-pee ruler away. :(lmao:

:(lmao:

I was thinking chris was a little bit over the top, easy way to tell a 5 gal bucket is 14.75 can you drive over one and not touch it?

wvyankee2 wrote:

How do you get 17 1/2" with a 2" lift and 27's? You need to put that pee-pee ruler away. :(lmao:

:afro: :(lmao:

chris has a special ruler, just for when the ladies come over :(lmao: Is that one of those that 1" = 3" ?

GunRunner wrote:

I was thinking chris was a little bit over the top, easy way to tell a 5 gal bucket is 14.75 can you drive over one and not touch it?

Well he can clear the five gal bucket just fine......

But with him and all the crap he totes I bet not! That only looks a inch or so above the bucket. That bucket looks like one of them shorter ones too, the one i measured had 4 rings at top his only has two, could that be a "special bucket" he uses too?

Is that a pee-pee bucket? Wait for the shake, piss boy. :D

Chris said he uses them MAGNUM buckets :(lmao:

Thats not a 5-gal, It's a 4....................

I think your right pate i enlarged the pic and it looks like it said 4 gal. Another exaggeration by the rhino king :(lmao:

Nope , it will clear a 5.
But marty is right. i must of mesured after just putting the wheels on.
and it was unloaded.

settled down. from the door. it is 15 and 7/8 right at 16.
at the skids its little over 14 1/2.

now if i jack it up and set it back down.
my original numbers were correct.
but that fully extended. so i agree i was wrong.

but as marty said settled down and if i get in it
and get out. from the sides its in the 15's...

i bet he had 40 lbs of air in them tires too..... makin em stand tall!!!

Gunny u must be getting another SxS?

You never know what the GunRunner may be up to :draw:

He will have a new one by Christmas i bet......